Common Home Light Switch Wiring Mistakes To Watch Out

electrical contractor adelaide

When you want to do your light switch wiring in your home, you should be aware of the mistakes that can cause danger in your home. By taking care of these dangers especially during installation, you will take care of some of the threats that may exists thus enabling you to improve safety as well as comfort in your homes. Here are some of the common home light switch wiring mistakes to watch out during installation:

  1. Overlamping during wiring

What it means is that a light fixture with a bulb of higher wattage can cause problems when fixed in fixture is not designed for. The intense heat of the bulb can scorch or even melt the socket as well as insulation on the wired on fixtures thus increasing the arcing risks sparks, which jump throughout the air especially from a given wire to another leading to electrical fires.

  1. Uncovered Junction Box

Because any junction box can house all splices, where these wires do connect to each other, or with a person might inadvertently damage them leading to a shock. An expert who does the wiring should ensure that these wires are not within reach since they might lead to electric shocks in many cases.

 electrician east melbourne

  1. Too Few Outlets

This means that Heavy reliance on power strips and extension cords that may be dangerous for the people who use the specific house. During wiring, the electrician need to use a heavy-duty extension cord of 14-gauge or even thicker. With a thicker wire, it will lower the number of the gauge number as opposed to using an undersized extension cord of 16-gauge or even smaller. Why so? Because it can overheat to ignite fire when loads are so heavy. When you suspect that the wiring was not done properly, you should ensure that you hire a licensed electrician who will patch these holes to avoid fire breakouts in your home.

  1. Overwired Panel

Any electrical panel has more circuits that handles too much electricity while handling numerous single-pole breakers. When you have tandem breakers or two circuits in a given slot, it will help the tandem breakers with the same high-amp and double-pole breakers capable of taking two slots within a circuit. By labelling every panel through specifying on how many circuits each panel should accommodate, it can help reduce the consequences of high power output that may lead to damages in your home.

 electrical contractor melbourne

  1. Aluminum Wiring

Using Aluminum Wiring means that you have a kind of wiring, which was used during the 1960s as well as ’70s especially as a copper substitute since it cheap. However, in many cases, people no longer consider it as safe. The main danger is that when aluminum corrodes especially when it is in contact with pure copper, it can lead to arcing as well as fires. You should ensure that your home light switch wiring is done on pure copper as a way of avoiding these mistakes that might lead to fire and huge losses.

In conclusion, the above are the top 5 home electrical wiring mistakes that you must consider whenever you want to do an electrical installation.

The Best Air Conditioning Unit For Your Home

In the heat of summer, every homeowner wishes that they had a system of air conditioning. If it is time for you to get your first air con system or you want to replace your old unit; the first step is choosing the right one. Cooling systems come in various designs including outdoor compressors, portable units, and central systems.

This guide from air conditioning Melbourne should help you choose the best one for your home.

air conditioner repair

1. Window Units

The “unitary” air con window units are self-contained and often take a window placement. All its components come packaged in the single unit hence the unitary reference. The system works by expelling heat through the side placed facing outside the window. It then blows cold air inside.

The size of window cooling systems varies. The sizing dictates the amount of cooling the unit can provide. Smaller homes can get efficient cooling throughout with a larger sized window unit.

2. Portable Air Con Systems

The portable air con also falls under the unitary models. It is self-contained and also mobile meaning that it can be moved from room to room. The unit often gets placed on the floor and exhausts heat through a window based hose vent.

Portable units operate considerably noisily compared to other air con systems. They also offer small-scale cooling covering less than 500 square feet. Portable cooling sytems work best to  provide cooling for individual rooms or where window-mounted systems are impractical.

3. Ductless Cooling Systems

The ductless or split cooling systems are synonymously referred to as PTACs ( packaged terminal air conditioners). They are often used in apartments, motels, and hotels. Homes that cannot accommodate forced air cooling systems have also started using these systems.

In the air conditioning maintenance, the air con features two packages placed a distance away from each other. One of the units functions as the condensing unit placed outside the house. The other serves as the evaporative unit placed inside the house. The terminal units are interconnected using a refrigerant tubing running through the wall.

4. Central Cooling Systems

Also referred to as forced air systems, central air cons provide a premium cooling solution for your home. It operates quietly, functions optimally, and offers enhanced cooling comfort when compared to the rest. Central air conditioning units feature two packaged units. They include an evaporative unit placed on your furnace’s plenum and the condensing unit that gets placed outside the house. A refrigerant tubing connects the two units.

The challenge with central systems is selecting one in a correct size that is appropriate for your home. Improper sizing causes performance and humidifying issues.

Choosing a cooling system may prove challenging if you cannot determine your particular cooling needs. Even smaller homes might still end up with the wrong air con unit because several factors affect the decision. The size, build, and square footage of your home determines your home’s cooling load needs. Working with a cooling systems professional can help you figure out what air conditioning system works best for your home and how to do air conditioning repair.

air conditioning repair

5 Benefits of Hiring an Experienced Electrician

electrician glen waverley

Whether it’s an electrical repair or you are giving electrical supply to your just completed new house, carrying out electrical operations on your own is NOT advisable. Among the important things, one should always keep into account when it comes to electricity is that electricity handling is a very specialized industry. Do-it-yourself’ projects are okay and well. However, when it comes to the electricity installation of a home, there are a number of reasons why a professional electrician Brisbane is the best option to consider. Here are key reasons why you need to hire them to sort out your electricity needs.

1. Professional Guarantee

Just like any other issue in your home, specialized electricians are the best choice when it comes to electrical work. Their operations in your home will always be backed by an inclusive insurance company and to top it up, a professional guarantee that will ensure professional electric work done to your home.

Remember that there are certain aspects that may come up during the electrical job. Therefore, it is usually an added advantage to the home owner when a pro is hired. This offers one protection, especially whenever an electrician suffers any form of injuries while working at on your home premises. In addition, one gets compensated in case his or her home/property gets damaged.

 commercial electrician melbourne

2. Excellent job

A professional electrician is always well equipped with the skills, tools and the knowledge that’s required to deal with all electrical problems. This is because these electricians will undergo training on repairs, installation, and maintenance of electrical jobs before being licensed. When you hire an electrical expert, you are definitely in for an excellent job.

3. Ensures one gets Government permits

As we are all aware, the government has set up stringent codes and measures which cover the electrical activities that are done within its borders. The best thing when hiring an electrical professional contractor is, he or she is well aware of how and where to get the required Australian permits. The contractor enables also the local inspector to inspect the job done and to either approve it or not.

4. Reliability

Reliability here will simply mean that one is assured that the electrical system will run well and effectively for a long period as it was initially designed to do. Professional electricians are very well-trained in handling, installing and maintaining such systems, therefore, will ensure the smooth running of the electrical system installed in one’s home.

 household electrical repairs

5. Ensure the protection of you Property

Wrong electrical installation may cause a lot of damage to your home electrical appliances which will mean more money will be spent in the repair of these appliances. Whenever your home needs an electrical installation, a professional electrician should be hired without hesitation. There’s no need in trying to do it yourself if you clearly don’t have a background in the electrical operations or installations.

Most of the electrical appliance can last approximately to over 10 years if properly taken care of and therefore you don’t want to keep replacing such valuables with such a long life span just because of unprofessional electrical installations. Call the certified electricians the next time. Well, these are just a few of the benefits that accompany the hiring professional electricians. I hope the information has to be of great use for electrical repairs.


Leave Your TV Outlet Installation To The Professionals

emergency electrical services

You are all excited with your new HDTV as you can finally enjoy your favorite movies and shows in brighter colors and vivid and accurate pictures. The only dampening aspect of getting a new HDTV is it’s installation as it has to be properly installed, preferably by electrical specialist for maximum safety and enjoyment.

One of the appealing aspects of flat panel TVs is its wall installation with concealed wiring. All the electrical and television signal wires have to pass through the walls and into the concealed junction boxes behind the mounting bracket. It’s a professional technician who ensures the TV outlet installation is properly fit against the wall, with minimal visible wiring.

The right position

While home decor magazines portray a sleek, flat panel TV mounted over a fireplace it’s not the best location for your TV. There is the risk of your TV catching fire if you have a wood-burning fireplace.

Besides, the fire generates heat and smoke which is not good for your TV. However things are different with a gas fireplace as they usually have vents for heat dispersal so there is no risk of the heat reaching your TV.


 local electrician sydney

You and your electrician Brisbane will have to decide on the best potion for your HDTV. It should be preferably mounted at eye level when you are seated as you strain your neck if it’s mounted too high.

Remember that plasma flat panels give a more consistent picture quality when viewed from the side. However the blacks in liquid crystal screens tend to turn grey, and colors shift to different tones if viewed from the side.

That’s why your electrician will suggest mounting your television as close to your normal line of sight while seated, and not at an angle as this is when the picture is clearest. If you have to mount your TV a bit higher, your electrician may suggest using a tilting wall mount to help angle the TV downwards.


Once the spot is decided, your electrician will mark the bracket spot by aligning two vertical studs in the wall. They will then cut an outlet-sized hole at the outlet’s height towards the base of the wall.

This is usually a foot from the floor and it is through this hole that signals cables pass from the equipment back to the TV’s back. Your technician will then use nose plates to terminate and conceal both junction boxes and let the cables pop out unobstructed.

Following the code

According to code, you need to have a metal junction box installed for the AC wire. Your electrical repair technician will either run the AC wire from the service panel in your home’s lower level to the new outlet’s location, or install a kit that jumps a nearby outlet to service the new outlet behind your television.

 electrical repairs

These kits comprise of the necessary new outlets and the Romex and extension cords needed for installation. It however is against the code to pass an extension cord or the TV”s power cord directly through the wall as the code accepts only shielded or unshielded Romex for in-wall use.

As so much goes into the proper TV outlet installation of your new HDTV, it’s imperative that you hire professional technicians to complete the job instead of you attempting to do it on your own.

Oven Troubleshooting And Repairs

oven repairing

Before you attempt to repair a malfunctional electric oven, it is imperative to take into consideration all the necessary safety precautions. Unlike the gas ovens, electric powered oven usually involves an enormous amount of energy flowing through the entire system, approximately 220 volts. So for you to create a safe and a conducive working environment you should just ensure that you either disconnect or shut off the power to your oven.

Even though ovens are usually extremely durable, there are a few problems that would occasionally arise with their continued use. Unfortunately, most of these problems are often complex, and you may not be able to troubleshoot them on your own. Issues such as no power, your oven not turning on as well as other problems can only be solved with the help of a qualified Melbourne electrician or a support engineer.

In this post, we will examine some of the most common oven problems and a brief and practical ways on how you can solve them personally.

 east brisbane electrician

 1. Power issues

The first move you should make when examining if your oven has a faulty power supply is to inspect the condition of the fuses on your device. Fuses that are faulty can potentially render any component in your house ineffective and are one of the primary reasons for power related problems around your home. If no sound or light is coming when your cooker is on, then you should try to heat up one of the hobs on your oven. If you realise that the hob glows and you can feel some warmth, then definitely your power supply is functional, and this implies that the issues are to do with the internal components of your machine.

 2. The bake element

If the heating element of your device works, then probably you have a bake element or wiring issue to deal with. On most models, the bake element is usually located on the bottom of the oven. It is black in colour and of the same size as a pencil. The bake element is typically connected to the oven by two screws. Eliminate these screws and pull out the bake element. After this, attach a 240V circuit to the terminal of the element. Connect your oven to a power supply and turn it on to see it bakes. If the light is on, just know that the bake element has burned out and the only solution is to look for a replacement. In some instances, you’ll find that the food will partially cook even when your bake element is faulty, and this is because the broil element is heating your food. If the light doesn’t come on, then the whole problem lies in your wiring.

 3. Wiring problems

The wiring of your oven is located on the back panel of your device. Check inside the back panel and see if there are any burnt terminals or wires. If any, remove it before replacing it with a nickel-plate terminal of high temperature.

 4. The door, as well as the control knobs, is getting too hot

This particular problem is common in appliances that do not have a cooling fan. A cooling fan blows cold air out from the top of the device thereby cooling the control knobs and doors. So in cases where there are no cooling fans, individual devices may feel sweltering to touch.

east brisbane electrician

 5. Thermostat

If your oven functions and even cooks at really low or high temperatures, check your thermostat’s sensing bulb. If you didn’t know, this particular bulb could sometimes come loose, ending up either on the floor of the oven or the heating element. On most occasions, the thermostat will require recalibration, a task that only needs the attention of a qualified and an experienced technician.

These are some of the most common problems which typically occur on your electric oven. Of course, there are others such as issues with the broil element, intermittent burners, your oven burning food or even the oven door failing to close properly.However, if even after conducting all these procedures and your oven still misbehaves, in such a case you will have to contact an experienced technician for relevant assistance.

What You Should Know About Electrical Surge Protectors

electrical power surges

Also known as voltage surges, electrical power surges are quick and temporary spikes in voltage within an electrical circuit. The occurrence of these surges is unavoidable and happens when something boosts the circuit’s electrical charge at some point. This particular boost increases the current that flows into or within your home’s electrical wiring thus affecting the appliances, lighting as well as other electrical equipment in your home. Power surges can be as a result of many different factors including lightning, faulty electrical wiring or even sudden turning on or off of a high power electrical appliances such as a large electric motor or your HVAC.

It is estimated that more than half of household electrical power surges are internal. Such surges occur a couple of times, especially when your home devices with motors either start up or shut off, diverting energy to and from other devices. In this regard, air conditioners and perhaps refrigerators are the biggest casualties, even though other smaller devices such as hair dryers can equally cause problems. On the other hand, external power surges, which commonly stem from outside your property, are usually caused by a tree limb touching a power line, a small animal getting trapped into a transformer or lighting striking a particular utility equipment.

electrical power surge protector

Why should you worry about electrical power surges?

Your home contains lots of items that are susceptible to power surges. As such, anything that has a microprocessor is especially vulnerable since they are incredibly sensitive that even a small power fluctuation of a 10-volt can potentially disrupt its normal functioning. Microprocessors are found in some household items such as cordless phones, refrigerators, washing machines, computers, as well as TVs. Large power surges caused by lightning strikes might cause massive damage such as frying circuits and the melting of plastic parts. Simply put, power surges can lead to cases of fire.

How can you protect your home appliances from incidences of power surges?

First and foremost, it is crucial to note that even the typical surge protector is not adequate to protect your appliances and electronics from a lightning strike. This means that the best thing you can always do is to unplug all your electrical devices during raging electrical storms. However, if you are residing in an area prone to faulty wiring, you should invest in a surge protector.

Point-of-use surge machines for surge protection, integrated with excellent grounding system can potentially protect your electrical appliances and electronics from even the most damaging power surges. It is worth mentioning that surge protection devices does not either arrest or suppress a surge, but typically diverts the surge successfully to the ground

Possible approaches to surge protection.

  • Point-of-use devices can provide protection to your appliances in your house, but for a more practical and effective approach to an adequate protection is to integrate point-of-use protection devices with another device such as a service entrance a power panel surge protector. By using two-tier surge protection, you’ll probably protect your entire home from the dangers of even some of the most powerful electrical surges.
  • Surge entrance protection devices typically mount on your primary power panel or even at the base of your electrical meter. This particular approach provides protection for the whole of your electrical system, including appliances such as light switches, outlets, motors, etc.


What should you look for when choosing the most efficient surge protector?

It is imperative to note there are numerous and different surge protection devices on the market, and this implies that the prospect of choosing the best that fits the needs of your home can be an awful experience. However, the general rule is always that the bigger the device, the better. In this regard, large refers to the Joule ratings, and this is the capacity of the surge protector to absorb electrical spikes.

For maximum protection, you should look for a device that lists at least six hundred joules or higher. If you didn’t know, anything lower than that might not be sufficient especially if your home usually experiences regular power spikes or you are planning to plug several devices into the strip. The most effective type of surge protection should be a whole house surge protector. It refers to a single device which connects to your primary electrical panel, thus protecting your entire home. These devices reduce the surge that occurs when lightning strikes your home or even if spikes happen in your main electrical line.

As always, you should contact your local electrician who has adequate knowledge regarding the installation of electrical surges.

Never Forget These 5 Things When Hiring An Electrical Contractor Melbourne

Because of the dangers involved, electrical work is not something that you should joke around with. A slight mistake might mean see your property razed down or your family/ friends might start planning your funeral. Rather than go through the worst, it’s better to take advantage of the expertise of a certified electrician Melbourne.

Searching for an electrician leads you to numerous options. Because you cannot work with all of them, you must compare services offered by different professionals to land on the best. During the hiring process, there are things you must not forget such as:

1.Certifications, Accreditation, And Registration

The first step is to ensure the electrician you want to work with has all the proper qualifications that are needed to offer the service. Ask for proof of certifications, accreditations, and registration with relevant bodies to confirm that the technician indeed has the right to handle the responsibilities laid before him/her. You can use websites such as licensed trades to check the authenticity of their papers.

2.Go Through Relevant Reviews

To know that you are in the right hands, it is important to find out what the contractor you want to hire has been up to. Read through various reviews online to know if the electrical contractor Melbourne offered excellent services to his/her clients in the past.

Do not be satisfied with what you read online. Go a step further to ask for references and call up the clients just to be sure that the electrician did not cook up the reviews.

3.Agree To A Quote Not A Rough Estimate

Before the electrician starts working on anything, ensure that you do not agree to a rough estimate, but a quote.

The quote should be well detailed, including actual prices, details of the task at hand, and a reasonable payment schedule. The fee schedule should outline any deposit that you have made and a payment calendar. It is important as it helps to avoid any misunderstandings when the electrician is doing their job.

Be on the lookout for any red flags that might read you are going to be exploited.

4.Get An Electrician Who Prioritizes Your Needs

The professional you opt to work with should listen to what you want. You do not want to hire someone who cannot attend to your services right away. Stay away from professionals who tell you that they are only available after weeks.

Even when it is not an emergency, the professional should start work right away so that you can continue your life without too many problems.

5.Do Not Go For The Cheapest Option

Avoid the electrical contractor Melbourne who offers the lowest rates. Read through the quotes keenly to get the person who is best suited for the job. Most of the time the contractors who offer the lowest rates end up doing a shoddy job which means you have to hire another competent electrician to clean up the mess. However, it does not mean that you should look for the most expensive as you may end up paying more for nothing.

Check Quick Spark for more information.

What is an Electric Oil Heater?

It’s that time of the year again when the days and nights get considerably colder as winter comes along. And with the onset of colder weather comes the need for additional or supplemental heating for your home.

Many options are currently available, but the electric oil heater is one that has been gaining popularity of late.

What is an Electric Oil Heater?

Also known as an oil-filled heater, column heater or oil-filled radiator, an electric oil heater uses convection heating and uses electricity instead of fuel burning to produce heat. The oil, in fact, is actually just used a heat reservoir, and not actually as fuel.

What are the Advantages of an Electric Oil Heater?

  1. A column heater is energy efficient.

An oil-filled heater has low wattage, so it won’t dramatically increase your electricity bill after every use. These heaters are able to generate a considerable amount of heat with minimal electricity, making them ideal for office and home settings.

  1. An oil-filled radiator is safe to use, even for long periods of time.

Because these heaters have low wattage, they are less likely to overheat. They can be used continuously for long hours with no risk of overheating.

  1. Electric Oil Heaters are kid and pet-friendly.

Operating a heater around the house where kids and pets constantly roam around can be nerve-wracking, but not with a column heater. Unlike other kinds of heaters, the exterior of an electric oil heater doesn’t heat up with use, so you don’t run the risk of kids or pets running around, brushing against the heater, and hurting themselves.

  1. A column heater is portable.

If you have several rooms in your home that need supplemental heating at different times of the day, you can easily move around a column heater between rooms, as most models come with an integrated wheel base. They are lightweight, so you can even move them around between floors, with some units weighing as little as ten pounds, possibly even less!

  1. An electric oil heater doesn’t emit carbon monoxide

An oil-filled radiator does not actually burn oil, so it doesn’t emit a dangerous gas like carbon monoxide. Unlike other heaters, in particular, propane heaters, the use of an electric oil heater won’t run the risk of carbon monoxide poisoning.

  1. A column heater is easy to use

An electric oil heater comes complete with various digital controls, including a timer, a thermostat that can be adjusted, and various heat settings. It also has an auto shut-off function for safety.

  1. An electric oil heater doesn’t require constant maintenance

As they are modern appliances with few components, a column heater doesn’t require regular heater maintenance. In the rare event when it malfunctions, manufacturers often provide warranties that would cover basic repairs.

A common misconception about oil-filled heaters is that the heating oil it contains need to be refilled or replaced, which is actually not the case, as this oil is never burned or used up. A column heater is expected to last you many years, working effectively without the need for any sort of repair, making them a very convenient appliance to have around the home.

DIY Air Conditioner Cleaning

A dependable air conditioner is an integral part of any home until it starts to malfunction. Very often, and usually out of the blue, your air conditioner just stops doing what it’s supposed to do, and it’s suddenly not the reliable appliance that cools your home to a nice, perfect temperature anymore.

When this happens most homeowners think it’s a case of their air conditioner being low on refrigerant, but this is not the only possible cause of this problem. More often than not, in fact, when your air conditioner can’t seem to blow cool air anymore, it’s because several of its many parts have been clogged by dirt.

Just like any other home appliance, your air conditioner needs regular cleaning and maintenance, and while there are experts and companies who can provide you with this service, cleaning your air conditioner unit yourself can be a less costly alternative – if you do it right. Read on to learn more about DIY air conditioner cleaning.   

  1. Prepare your tools and cleaning materials

Don’t get any work done on your air conditioner without having all of your equipment and materials in one place first. The basic items you will need for AC cleaning include the following:

  • Screwdrivers and other tools to help you open up and disassemble your air conditioner
  • Rags and towels
  • Your choice of cleaning product
  • A handheld vacuum
  • A hose connected to a water source
  1. Turn off and unplug the air conditioner unit

Before you start to open and inspect your air conditioner, be sure it has been shut off, and unplugged. Safety is of utmost importance when it comes to dealing with electrical appliances.

  1. Turn your attention to the filter

Start with the easiest portion to clean – the air filter. This is an air conditioner’s first line of defence against airborne dirt and foreign particles. Remove the air filter from the unit, take it outdoors and shake off all the dirt that’s clung to it. If that isn’t enough, use the vacuum to ensure you’ve cleaned it thoroughly. Depending on your air conditioner model, you can also choose to hose down the filter, but be sure to let it completely dry first before installing it back to your unit. Finally, if your filter is beyond cleaning, replacing it with a new one can also be an option.

  1. Clean the fan coil

Pick up your screwdriver to disassemble the air conditioner so you can get to the fan coil of your indoor unit. It’s important to keep this part of the air conditioner clean as it is largely responsible for blowing cool air. To clean the fan coil, use your preferred cleaning solution and spray lightly. Wait for a few minutes before rinsing the fan coil with water, which should easily be drained from the drip pan. Make sure the fan coil has dried from all the rinsing before assembling the air conditioner back.  

  1. Head outside to clean the condenser coil

If your air conditioner model has an outdoor unit, be sure to clean the condenser coil found inside it, and clean it in a similar way to how you cleaned your indoor unit’s fan coil.

5 Reasons to Hire Professional Cleaning Service for Home

Cleaning the home is a very tough job. You need to clean home every second day for the amount of dirt and dust that accumulate in the house. If you have kids, then you should clean your home more often. People often spend long hours on Sunday or any other holiday cleaning their home. There are many professional home cleaning services available now. You should hire these cleaning services for the following reasons.

1. They will do a thorough cleaning of the house. They will make sure that your carpet is vacuumed, surfaces are cleaned and disinfected. It will ensure that no dust mites or allergens are present.

2. You won’t have to spend your Sunday for cleaning anymore. You can spend some quality time with your family instead. You can make special dinner or watch movies together.

3. A professional cleaner has the best technology and cleaning products to use. As they are experts in the field, they know about the latest cleaning products. With so many cleaning products and equipment in the market, it can be confusing to buy the right one. The professional cleaners know about these products and technology well. They will use them in the right places.

4. If the house is not cleaned properly, germs, insects, dust mites, and rodents will appear. Many household vacuum cleaners don’t have the technology to pick up dust mites or other small allergen particles from carpets, sofas or beds. The professional cleaners will have the right technology to pick up the smallest particles.

5. Professional cleaners won’t overlook any area of the house. They know where to look for dirt and dust. They will reach places where we may never do to clean dirt.

You should get your home cleaned by professionals at least once of twice a year. If you can afford, you should do it more regularly. Professional cleaners will keep your home clean and germ-free.